Click For Crochet Abbreviations List
Strict lines of silhouette, a laconic pattern and an original decoration-clasp in the form of a black decorative ring are the three main components of a beautiful jacket.
Size: S / M / L-XL
Distinguishing data for sizes M and L-XL are given in brackets and outside brackets respectively. If only one value is specified, then it applies to all sizes.
YOU WILL NEED
300 (350) 400 g of gray melange yarn (65% wool, 20% polyacryl, 8% cashmere, 7% elite, 150 m / 50 g);
knitting needles number 5;
1 decorative black ring with a diameter of 70 mm with a pin.
PATTERNS
Facial surface: faces. R. - persons. n., out. R. - out. P.;
Semipatent pattern: knit according to the pattern. In width, start with a loop and a loop of loops up to the 1st arrow, repeat between arrows 2 points of rapport, end with loops or a loop after the 2nd arrow. In height, perform from 1st to 4th p. 1 time, then repeat the 3rd and 4th p. Attention! The double crochet is only considered as 1 st.
Nodular region: see . All details knit with nodular edges.
Highlighted cuts from the right edge: chrome. p., 2 p. knit according to the drawing, next item knit as 2 items together of persons with an inclination to the left ( see. Basics );
Marked downs from the left edge: knit a row to the last 5 p., Then knit 2 p. Of persons together. ( see. Basics ), 2 p. - according to the drawing, chrome. P.
As a result, the selected decreases at the beginning and end of the row are reduced by 1 p.
KNITTING DENSITY
Semipatent pattern in a slightly stretched state: 19.5 p. And 40 p. = 10 x 10 cm.
Back
On knitting needles dial 85/93/101 p. And knit for the roller faces. smooth surface 2 cm (= 7 p.), starting from 1 out. row. Continue to work with a semi-patent pattern. At a height of 28/30/32 cm from the roller for armholes, close on both sides, first 2 p., Then in each 2 r. 1 x 2 p. And 4/4/6 x 1 p., Performing the marked decreases, we get on the needles 66/77/81 p. Next, knit directly. At a height of 21/21/22 cm from the beginning, the armholes for shoulder bevels should be closed on both sides by 5/7/7 p., Then in each 2nd p. 2 x 6/7/8 p. Simultaneously with the 1st decrease for shoulder bevels, close the central 15 p. For the neckline cutout according to the figure and finish both sides separately. To round the neckline, close from the inner edge in every 2 r. 2 x 5 p. On this loop one side will be closed.
The second side finish symmetrically.
Left shelf
On knitting needles dial 47/51/55 p. And knit for the roller faces. smooth surface 2 cm (= 7 p.), starting from 1 out. a number of out. Continue to work with a semi-patent pattern. Sew from the right edge to be done as for the back, we will get 39/43/45 p. On the knitting needles. At a height of 7/7/8 cm from the beginning, open the neck for the neckline from the left edge of 16 p., Then for the bevel in each 2 m . 6 x 1 p., Performing the selected reduction. Bevel the shoulder from the right edge as for the back.
Right shelf
Knit symmetrically to the left shelf.
Sleeves
On knitting needles dial 63/63/67 p. And knit for the roller faces. smooth surface 2 cm (= 7 p.), starting from 1 out. a number of out. Continue to work with a semi-patent pattern. For bevels, run on both sides in the 7th p. from roller 1, a marked decrease, then in each 2 r. 23/23/25 times in 1 highlighted decrease. At a height of 13.5 / 13.5 / 14.5 cm from the roller, close the remaining 15 p.
The second sleeve is the same.
Assembly
Moisten the parts and allow to dry. Make seams and seams of the rollers so that after tightening the roller, the seam is on the inside. Sew the seams of the sleeves after the roller by another 1.5 cm. Stitch the sleeves. Secure the rollers over the seams with a few stitches. Use a decorative ring as a fastener.